GATE Exam 2018 Petroleum Engineering (PE) Question Paper With Answer Key

General Aptitude (GA) Set-1

Q. 1 – Q. 5 carry one mark each.

1. “ Going by the _________ that many hands make light work, the school _______ involved all the students in the task.”

The words that best fill the blanks in the above sentence are

(A) principle, principal

(B) principal, principle

(C) principle, principle

(D) principal, principal

Answer: (A)

2. “ Her _______ should not be confused with miserliness; she is ever willing to assist those in need.”

The word that best fills the blank in the above sentence is

(A) cleanliness

(B) punctuality

(C) frugality

(D) greatness

Answer: (C)

3. Seven machines take 7 minutes to make 7 identical toys. At the same rate, how many minutes would it take for 100 machines to make 100 toys?

(A) 1

(B) 7

(C) 100

(D) 700

Answer: (B)

4. A rectangle becomes a square when its length and breadth are reduced by 10 m and 5 m, respectively. During this process, the rectangle loses 650 m2 of area. What is the area of the original rectangle in square meters?

(A) 1125

(B) 2250

(C) 2924

(D) 4500

Answer: (B)

5. A number consists of two digits. The sum of the digits is 9. If 45 is subtracted from the number, its digits are interchanged. What is the number?

(A) 63

(B) 72

(C) 81

(D) 90

Answer: (B)

Q. 6 – Q. 10 carry two marks each.

6. F or integers 𝑎, 𝑏 and 𝑐, what would be the minimum and maximum values respectively of 𝑎 + 𝑏 + 𝑐 if log |𝑎| + log |𝑏| + log |𝑐| = 0?

(A) -3 and 3

(B) -1 and 1

(C) -1 and 3

(D) 1 and 3

Answer: (A)

7. Given that 𝑎 and 𝑏 are integers and 𝑎 + 𝑎2 𝑏3 is odd, which one of the following statements is correct?

(A) 𝑎 and 𝑏 are both odd

(B) 𝑎 and 𝑏 are both even

(C) 𝑎 is even and 𝑏 is odd

(D) 𝑎 is odd and 𝑏 is even

Answer: (D)

8. From the time the front of a train enters a platform, it takes 25 seconds for the back of the train to leave the platform, while travelling at a constant speed of 54 km/h. At the same speed, it takes 14 seconds to pass a man running at 9 km/h in the same direction as the train. What is the length of the train and that of the platform in meters, respectively?

(A) 210 and 140

(B) 162.5 and 187.5

(C) 245 and 130

(D) 175 and 200

Answer: (D)

9. Which of the following functions describe the graph shown in the below figure?

(A) 𝑦 = ||𝑥| + 1| − 2

(B) 𝑦 = ||𝑥| − 1| − 1

(C) 𝑦 = ||𝑥| + 1| − 1

(D) 𝑦 = ||𝑥 − 1| − 1|

Answer: (B)

10. Consider the following three statements:

(i) Some roses are red.

(ii) All red flowers fade quickly.

(iii) Some roses fade quickly.

Which of the following statements can be logically inferred from the above statements?

(A) If (i) is true and (ii) is false, then (iii) is false.

(B) If (i) is true and (ii) is false, then (iii) is true.

(C) If (i) and (ii) are true, then (iii) is true.

(D) If (i) and (ii) are false, then (iii) is false.

Answer: (C)

Petroleum Engineering

Q. 1 – Q. 25 carry one mark each.

1. The Taylor series expansion of the function,

around 𝑥 = 0 (up to 4th order term) is:

Answer: (B)

2. The inverse of the matrix is

Answer: (C)

3. The line integral of a vector function over a curve C in a simply connected domain D in space, is defined by:

The line integral is independent of path in D. 𝐹1, 𝐹2, and 𝐹3 are continuous, and have continuous first partial derivatives in D. 𝐶′ is a closed curve in D.
Which one of the following is NOT ALWAYS true in domain D?

Answer: (B)

4. Which one of the following is the integrating factor (IF) for the differential equation, ?

(A) 𝑒tan 𝑥

(B) 𝑒cos 𝑥

(C) 𝑒− tan 𝑥

(D) 𝑒sin 𝑥

Answer: (A)

5. A phase diagram of a black oil is shown in the figure (Y is the critical point).

Match the following:

(P) Curve XY (I) Dew point curve

(Q) Curve YZ (II) Single phase liquid

(R) Phase I (III) Bubble point curve

(S) Phase II (IV) Single phase gas

(A) P-I, Q-III, R-II, S-IV

(B) P-III, Q-I, R-II, S-IV

(C) P-III, Q-I, R-IV, S-II

(D) P-I, Q-II, R-III, S-IV

Answer: (B)

6. Match the following chemicals to their respective oilfield applications:

(P) Hydrate inhibitor

(I) Formaldehyde

(Q) Well stimulation

(II) Xanthan gum

(R) Drilling fluid biocide

(III) Methanol

(S) Viscosifier

(IV) Hydrochloric acid

(A) P-IV, Q-III, R-II, S-I

(B) P-III, Q-I, R-IV, S-II

(C) P-I, Q-III R-IV, S-II

(D) P-III, Q-IV, R-I, S-II

Answer: (D)

7. The CH4-hydrate equilibrium curve (dashed) and CO2-hydrate equilibrium curve (solid) on a pressure-temperature plane above 0°C are shown in the figure. The two curves divide the plane in four non-overlapping regions. In which region are CO2-hydrates stable and CH4– hydrates unstable?

(A) I

(B) II

(C) III

(D) IV

Answer: (B)

8. Plot of ratio of pressure to gas compressibility factor (P/Z) vs. cumulative gas production (Gp) for a gas reservoir (represented by solid curve in the figure) was shown to a reservoir engineering student.

The student made the following statements:

(I) A water aquifer is attached to this gas reservoir.

(II) P/Z vs. Gp curve must always be a straight line for water encroachment in a gas reservoir.

(III) The ultimate gas recovery is diminished due to water encroachment.

Which of the above statements are TRUE?

(A) Only I and II

(B) Only II and III

(C) Only I and III

(D) I, II, and III

Answer: (C)

9. Waste water from oil industry consists of oil in free and emulsified forms. The oil in the free form can be recovered by:

(A) Aerated lagoons

(B) Trickling filters

(C) Gravity separators

(D) Biological oxygen pond

Answer: (C)

10. A reservoir model consisting of two porous matrices M and N, separated by a fracture, is shown in the figure. The matrices are strongly water-wet and are saturated with oil of specific gravity 0.8. Water is injected only in the fracture at injection well A. If the Reynolds number for the flow in the fracture conduit is assumed to be less than unity, which one of the following force will dominate oil recovery from the porous matrix M during the water-flood operation?

(A) Capillary force

(B) Gravity force

(C) Viscous force

(D) Inertial force

Answer: (A)

11. A fractional flow curve is given for a core for which the irreducible water saturation is 0.2 and the residual oil saturation is 0.3. The initial water saturation in the core is 0.3. If Welge’s method is applied to find the breakthrough saturation and fraction flow of water at breakthrough, which point should be used in the figure to draw a tangent line to the fractional flow curve.

(A) I

(B) II

(C) III

(D) IV

Answer: (D)

12. Which one of the following curves represents behavior of oil phase viscosity as a function of pressure in the reservoir (where, Pb is the bubble point pressure of oil)?

(A) Curve I

(B) Curve II

(C) Curve III

(D) Curve IV

Answer: (D)

13. Pick out the INCORRECT statement.

(A) Flash point is always lower than fire point.

(B) Pour point of lube oil can be reduced by removing the wax from it.

(C) Fracturing is a well stimulation technique.

(D) Coal bed methane typically contains more than 60% CO2.

Answer: (D)

14. Which one of the following phenomena encountered during flooding is desirable for increasing oil recovery from a reservoir?

(A) Viscous fingering

(B) Formation damage

(C) Increase in mobility ratio

(D) Decrease in capillary pressure

Answer: (D)

15. CO2 foams are used for enhanced oil recovery due to which of the following reasons?

(I) It can be used for CO2 sequestration

(II) CO2 can exist in the form of a dense fluid at reservoir conditions

(III) CO2 can convert to hydrocarbon at the reservoir temperature and pressure

(IV) Solubility of CO2 in oil is higher compared to gases like N2

(A) Only I, II, and III

(B) Only I, II, and IV

(C) Only II, III, and IV

(D) Only I, III, and IV

Answer: (B)

16. Which one of the following is FALSE about a typical offshore deepwater oil spill?

(A) Using boom boats to prevent spilled oil from spreading

(B) Allowing the spill to reach the shore before clearing

(C) Burning of spilled oil

(D) Using a skimmer to collect the oil

Answer: (B)

17. Which one of these methods is NOT commonly used to deal with the problem of soil contamination by oil spillage?

(A) Biodegradation

(B) Leaching out the oil

(C) Soil recycling

(D) Using rain water to wash the contaminants

Answer: (D)

18. The factor on which the selection of an offshore platform for the reservoir does NOT depend:

(A) Water depth

(B) Reservoir fluid properties

(C) Sea bed conditions

(D) Best case weather forecast

Answer: (D)

19. Which one of the following options is correct about the effects of steam stimulation in increasing the oil production rate?

(I) Reduces the oil viscosity

(II) Increases the formation damage

(III) Reduces the interfacial tension

(IV) Increases the oil viscosity

(A) Only I and II

(B) Only II and III

(C) Only III and IV

(D) Only I and III

Answer: (D)

20. Which one of the following is INCORRECT about oil based drilling muds?

(A) Good rheological properties at higher temperatures (as high as 250oC)

(B) Effective against corrosion

(C) Detection of gas kick is difficult

(D) Less inhibitive than water based muds

Answer: (D)

21. Assume that viscous, gravity, and capillary are the only dominant forces for fluid flow in a given reservoir, a cone formed around the perforation zone will break into the well, when 

(A) capillary forces are more than viscous and gravity forces.

(B) viscous forces are more than gravity forces.

(C) gravity forces are more than capillary forces.

(D) viscous and gravity forces are equal.

Answer: (B)

22. Two complex numbers,  are related as follows:

where,  is a scalar. Given principal argument of the principal argument of  ______________. (rounded-off to two decimal places. (Use 𝜋 = 3.14)

Answer: (2.50 to 2.70)

23. A cylindrical sandstone core, 7.5 cm long and 3.5 cm diameter has grain density of 3 g/cm3. If the mass of the dry core is 200 g, the porosity of the core is __________%. (rounded-off to two decimal places)

Answer: (7.25 to 7.75)

24. In an oil reservoir the current average pressure is below bubble point pressure of the oil. The current oil production rate is 103 m3/day and total gas production rate is 105 m3/day at STP conditions (25°C and 1 atm). The formation volume factor of the oil is 1.2 and that of gas is 0.01 The dissolved gas oil ratio is 10  of soil

The gas flow rate at bottom-hole conditions is ______× 102 m3 per day. (rounded-off to two decimal places)

Answer: (8.90 to 9.10)

25. Exponential decline curve is to be used to estimate the oil reserves of a well. The current oil production rate is 1000 m3 per day and yearly decline rate is 6% per year. If the minimum oil flow rate economically sustainable for the well is 1 m3 per day, the reserves (economically producible) associated with the well are _____ × 106 m3. (rounded-off to two decimal places. Use 1 year = 365 days)

Answer: (5.80 to 6.20)

Q. 26 – Q. 55 carry two marks each.

26. The probability density for three binomial distributions (D1, D2, and D3) is plotted against number of successful trials in the given figure.

Each of the plotted distributions corresponds to a unique pair of (n, p) values, where, n is the number of trials and p is the probability of success in a trial. Three sets of (n, p) values are provided in the table.

Pick the correct match between the (n, p) set and the plotted distribution.

(A) Set I – D1, Set II – D2, Set III – D3

(B) Set I – D3, Set II – D1, Set III – D2

(C) Set I – D2, Set II – D3, Set III – D1

(D) Set I – D2, Set II – D1, Set III – D3

Answer: (B)

27. Which of the following statements are true about Natural Gas Hydrates?

Natural gas hydrates:

(I) are formed under low temperature and high pressure.

(II) can store approximately 160 m3 of gas per m3 of hydrate at 25 oC and 1 atm.

(III) formation is an endothermic process.

(IV) are potential sources of methane.

(A) Only II, III & IV

(B) Only I, II & III

(C) Only I, II & IV

(D) Only I, III & IV

Answer: (C)

28. Pwf (bottom-hole well flowing pressure) vs. Q (flow rate) plots show the inflow performance relation (IPR) and vertical lift performance (VLP) curves. Figure I shows VLP curves for two well head pressures Phw1 and Phw2. Figure II shows VLP curves for two well diameters D1 and D2. Which one of the following statements is true?

(A) Phw1 > Phw2 and D1 < D2

(B) Phw1 > Phw2 and D1 > D2

(C) Phw1 < Phw2 and D1 < D2

(D) Phw1 < Phw2 and D1 > D2

Answer: (A)

29. Match the following:

(P) Weber Number (I) Ratio of inertial force to viscous force

(Q) Froude Number (II) Ratio of convective heat transfer to conductive heat transfer

(R) Reynolds number (III) Ratio of inertial force to interfacial force

(S) Nusselt number (IV) Ratio of inertial force to gravitational force

(A) P-III, Q-IV, R-I, S-II

(B) P-III, Q-II, R-I, S-IV

(C) P-II, Q-III, R-IV, S-I

(D) P-IV, Q-III, R-I, S-II

Answer: (A)

30. A dilute mixture of coal and sand particles, both of diameter 100 μm and densities 1800 kg/m3 and 2600 kg/m3, respectively, is to be classified by elutriation technique using water (density 1000 kg/m3, viscosity 10-3 Pa.s). Assuming Stokes law is applicable, the minimum settling velocity of the particles in the mixture is (g = 9.81 m/s2):

(A) 4.36 × 10-3 m/s

(B) 8.72 × 10-3 m/s

(C) 2.18 × 10-3 m/s

(D) 1.29 × 10-3 m/s

Answer: (A)

31. Oil flow rate and flowing bottom-hole pressure (FBHP) recorded with time during a multirate well test are shown.

Let k is the reservoir permeability, h is the formation thickness and μ is the viscosity of the oil. Δ𝑃𝐷(𝑡) is constant-rate dimensionless pressure drop as a function of time. The total pressure drop till time, t, where t > t1, will be:

Answer: (A)

32. Which one of the following options presents the correct combination? 

(P) Reservoir limit test (I) Communication between wells

(Q) Modified isochronal test (II) Ideally zero flowing bottom hole pressure

(R) Interference test (III) Extended drawdown test

(S) Absolute open flow potential (IV) Drawdown and build-up test of equal duration

(A) P-II, Q-III, R-I, S-IV

(B) P-IV, Q-I, R-III, S-II

(C) P-III, Q-IV, R-I, S-II

(D) P-I, Q-III, R-IV, S-II

Answer: (C)

33. Which one of the following options presents the correct combination?

(P) Roller Cone bits (I) Long and widely spaced teeth

(Q) PDC bits (II) Journal (Pin) angle

(R) Soft formation (III) Short and wider teeth

(S) Hard formation (IV) Size of the cutting

(T) Back rake angle (V) 1400oC and 6×105 psi

(A) P-II, Q-V, R-I, S-III, T-IV

(B) P-III, Q-IV, R-I, S-II, T-V

(C) P-III, Q-II, R-IV, S-I, T-V

(D) P-II, Q-V, R-III, S-I, T-IV

Answer: (A)

34. Primary and secondary indicators of kick in a well where the indicators are:

1) flow rate increase,

2) gas, oil or water-cut muds,

3) pit volume increase,

4) flowing well with mud pump shut-off,

5) reduction in drill-pipe weight,

6) drilling break.

Which one of the following presents the correct combination?

(A) Primary (1, 3, 5) and Secondary (2, 4, 6)

(B) Primary (1, 2, 3) and Secondary (4, 5, 6)

(C) Primary (1, 2, 4) and Secondary (3, 5, 6)

(D) Primary (1, 3, 4) and Secondary (2, 5, 6)

Answer: (D)

35. Relative permeability curve for the two rock types (X: solid line and Y: dashed line) are shown in the diagram, where Sw is the fractional water saturation. Which one of the following statements is correct about wettability and consolidated nature of the two rock types?

(A) X is more consolidated and mixed wet, Y is less consolidated and water wet

(B) X is more consolidated and water wet, Y is less consolidated and mixed wet

(C) X is less consolidated and mixed wet, Y is more consolidated and water wet

(D) X is less consolidated and water wet, Y is more consolidated and mixed wet

Answer: (C)

36. Which one of the following options presents correct combinations of exploration methods with their respective frequency of operation?

(P) Seismic (I) ~106 Hz

(Q) Sonic (II) ~102 Hz

(R) Controlled Source EM (III) ~104 Hz

(S) Ultrasonic (IV) ~1 Hz

(A) P-IV, Q-II, R-I, S-III

(B) P-II, Q-III, R-IV, S-I

(C) P-II, Q-I, R-IV, S-III

(D) P-IV, Q-I, R-II, S-III

Answer: (B)

37. Which one of the following options presents the correct combinations?

(P) Borisov’s (I) Critical rate correlation in vertical wells with coning

(Q) Schols’ ( I I ) H o r i zontal well performance relation

(R) Efros’ (III) Vertical well performance relation

(S) Wiggins’ (IV) Critical rate correlation in horizontal wells with coning

(A) P-II, Q-IV, R-I, S-III

(B) P-IV, Q-III, R-II, S-I

(C) P-IV, Q-II, R-III, S-I

(D) P-II, Q-I, R-IV, S-III

Answer: (D)

38. Which one of the following options represents the typical sequence of applying cut-offs for pay zone identification in a conventional reservoir?

(A) porosity, saturation, shale

(B) porosity, permeability, saturation

(C) shale, porosity, saturation

(D) shale, porosity, permeability

Answer: (C)

39. Which one of the following options represents the correct sequence of arrival of acoustic wave energy recorded in a sonic log?

(A) shear, surface, compressional

(B) compressional, shear, surface

(C) surface, shear, compressional

(D) compressional, surface, shear

Answer: (B)

40. The variation of the amount of salt in a tank with time is given by,

where, 𝑥 is the amount of salt in kg and 𝑡 is the time in minutes. Given that there is no salt in the tank initially, the time at which the amount of salt increases to 200 kg is __________ minutes. (rounded-off to two decimal places)

Answer: (10.50 to 12.50)

41. Solve the given differential equation using the 2nd order Runge-Kutta (RK2) method:

Use the following form of RK2 method with an integration step-size, ℎ = 0.5:

The value of 𝑦(𝑡 = 0.5) =__________________. (rounded-off to two decimal places)

Answer: (3.12 to 3.26)

42. A box contains 100 balls of same size, of which, 25 are black and 75 are white. Out of 25 black balls, 5 have a red dot. A trial consists of randomly picking a ball and putting it back in the same box, i.e., sampling is done with replacement. Two such trials are done. The conditional probability that no black ball with a red dot is picked given that at least one black ball is picked, is __________. (in fraction rounded-off to two decimal places)

Answer: (0.76 to 0.80)

43. A cylindrical pipeline of length 30 km is transporting naphtha. Pressure sensors are attached along pipe length to detect leaks. Under steady-state, leak-free operation, there is a linear pressure drop along the length (z) of the pipeline. If a leak occurs, the pressure profile develops a kink at the leak point 𝑧leak.

Assume that there is only one leak-point (4 km < 𝑧leak < 27 km) and a new steady-state is reached. The steady-state pressure measurements at four locations along the pipe-length are provided in the table. The location of the leak-point using the gradient intersection method is _______________km. (rounded-off to two decimal places)

Answer: (7.20 to 7.80)

44. A dry core was subjected to the mercury injection test in the laboratory. Following are the related details:

Average formation porosity = 0.2

Formation volume factor, BO = 1.2 reservoir-bbl/STB

Oil API° = 32, Specific gravity of water = 1.1

Hydrostatic gradient = 0.433 psi/ft

(𝜎𝑂𝑊 cos 𝜃)res = 26 dyne/cm, where 𝜎𝑂𝑊 is the oil-water interfacial tension and 𝜃 is the contact angle

(𝜎𝐴𝑀 cos 𝜃)lab = 367 dyne/cm, where 𝜎𝐴𝑀 is air- mercury interfacial tension and 𝜃 is the contact angle

Average drainage area = 80 acres

(1 acre-ft = 7758 bbl)

The Table shows the laboratory data for capillary pressure at different mercury saturations.

and the average water saturation (𝑆𝑊) for the productive column is 0.25. The Original Oil in Place (OOIP) in the productive column where 𝑆𝑊 ≤ 0.5 is ___________ MMSTB. (rounded-off to one decimal place)

Answer: (105.00 to 109.00)

45. A well is drilled with water based mud. The water saturation in the completely flushed zone (no formation fluid residual) is given by,

where, Rmf and Rxo are the mud filtrate resistivity and flushed zone resistivity, respectively.

Use, a = 1.0 and Rxo = 25 Rmf.

The calculated porosity (ϕ) of the formation is ______. (in fraction rounded-off to two decimal places)

Answer: (0.19 to 0.21)

46. An oil well is tested at a flow rate (Q) of 50 BOPD. The bottom hole flowing pressure (Pwf) is 500 psia. The shut-in pressure is 1000 psia. If Pwf is lowered to 300 psia and assuming the Vogel’s correlation holds, the estimated flow rate in the oil well is ______BOPD (rounded-off to two decimal places). The Vogel’s correlation is:

Answer: (61.00  to 63.00)

47. Using Miller, Dyes and Hutchinson (MDH) method, the skin factor of an oil well is found to be 𝑠 = – 3.5.

The reservoir and fluid properties are:

Formation porosity is 0.20

Total compressibility is 2.5 × 10-5 psia-1

Oil viscosity is 1.5 cP

Wellbore radius is 0.5 ft

Flowing bottom hole pressure at Δt = 0 is 2830 psia

Shut in pressure at Δt = 1 hr (PΔt=1hr) is 3000 psia

Slope of middle time region (MTR) line in MDH plot is 190 psia/cycle.

The permeability of the reservoir is __________mD. (rounded-off to two decimal places)

Answer: (25.00 to 29.00)

48. An oil well (producing under expansion drive only) in a reservoir is subjected to two pressure build-up tests. The average formation thickness of the reservoir is 13 ft, the total compressibility is 1×10-5 psia-1, and porosity is 0.2. The average formation volume factor of oil is 1.3 reservoir-bbl/STB. Average reservoir pressure during the first test and the second test was found to be 3500 psia and 3200 psia, respectively. If the oil produced between the two pressure build-up tests in 180 days is 250 STB/day, the area of the reservoir is __________acres. (rounded-off to two decimal places) (Use: 1 acre = 43560 ft2, 1 bbl = 5.615 ft3)

Answer: (960.00 to 970.00)

49. A well in a very large reservoir has a wellbore radius of 10 cm. The sandstone, with a porosity of 0.25 and 12% (by grain volume) calcite (CaCO3), is to be acidized with a preflush (HCl solution) so as to dissolve all the calcite upto a distance of 1 m from the wellbore. 1 m3 of preflush is able to dissolve 0.082 m3 CaCO3. Assume that the reaction between HCl and CaCO3 is instantaneous. The minimum preflush volume required per meter of the formation thickness is ______________m3. (rounded-off to two decimal places)

Answer: (4.40 to 5.50)

50. At a particular temperature, the vapour pressure of benzene and toluene are 4 atm and 1.2 atm, respectively. The composition of the liquid at equilibrium is 0.5 moles of benzene and 0.5 moles of toluene. Assuming ideal gas and ideal solution, the equilibrium vapour phase mole fraction of benzene is ________ . (rounded-off to two decimal places)

Answer: (0.72 to 0.80)

51. Saturated steam at 0.7 atm and 90°C condenses on a vertical pipe of 2 cm outside diameter and 40 cm length. The average condensation heat transfer coefficient on the tube is 12000 W/m2K. The outside surface temperature of the pipe is maintained constant at 85°C. The enthalpy values for saturated steam and condensate are 2660 kJ/kg and 375 kJ/kg, respectively. The rate of steam condensation is ____ kg/h. (rounded-off to two decimal places)

Answer: (2.10 to 2.60)

52. Oil is being transported between two reservoirs with the help of three parallel pipes at steady state. The diameters of these pipes are 2 cm, 3 cm and 4 cm, respectively. The pipes are equal in length and the flow is laminar. The discharge through the 4 cm diameter pipe is 50 liters/s. The discharge through the 2 cm diameter pipe is _____ liters/s. (rounded-off to two decimal places)

Answer: (3.00 to 3.20)

53. A driller finds an oil reservoir with a gas cap starting at a depth of 1000 m from the surface. The gas-oil contact was found at 1100 m depth and water-oil contact was found at 1300 m depth. The water pressure in the aquifer below the oil zone varies with depth from the surface (h, in meters) as, P = h × 104 Pa. The density of the oil is 900 kg/m3 and that of the gas is 5 kg/m3 at the reservoir condition. The minimum density of the mud needed to stop the gas kick when the driller reaches at the top of the gas cap is _____kg/m3. (rounded-off to two decimal places. Use g = 9.81 m/s2)

Answer: (1115.00 to 1160.00)

54. The viscosity, μ (in Pa.s) of a power law fluid as a function of shear rate, 𝛾̇ (in s-1) is given by the following relation:

This power law fluid lies between two infinitely large horizontal parallel plates separated by a distance (h) of 10-3 m. The top plate is moving horizontally at a velocity (v) of 10-3 m/s and the bottom plate is held stationary. Assuming laminar flow and neglecting gravity, the absolute value of steady-state shear stress acting on the bottom plate is ______ Pa. (rounded-off to two decimal places)

Answer: (0.49 to 0.51)

55. A heterogeneous rectangular rock of cross-sectional area 1 m2 perpendicular to the flow is being flooded by water to measure the effective permeability from cross-section AA’ to cross-section CC’.

The pressure at the cross-sections AA’, BB’, and CC’ is 2 bar, 1.5 bar, and 1 bar, respectively. The permeability in mili-Darcy and lengths AB and BC in meters are given in the figure. The effective permeability of the rock from AA’ to CC’ is ______mD.
(rounded-off to two decimal places)

Answer: (2.00 to 2.50)

Latest Govt Job & Exam Updates:

View Full List ...

© Copyright Entrance India - Engineering and Medical Entrance Exams in India | Website Maintained by Firewall Firm - IT Monteur